Skip to main content

Thread: D-Link DWA-652 on Toshiba Laptop

-

i feel really close @ getting connected.

native ath9k driver did not work. blacklisted driver , proceeded load windows driver came card through ndiswrapper.

system sees wireless router not connected router. circle of death of trying connect though.

replaced network manager wicd.

try , connect, after setting preshared key, , stops @ end saying not obtain ip address.

try set static ip, , @ end comes with, "could not contact wireless access point".

please help, feel close getting connected don't know if setting on router need change or different driver. driver should fine i'm no expert.

have 2 other computers wireless'ly connected router , 1 of them connected via dual boot, ubuntu , win7, @ least these 2 computers don't have issues connecting router.

looking suggestions, please! , yes throwing laptop out window acceptable suggestion, or going live winxp installed on instead. btw: had no problems getting wireless connection laptop when had winxp installed, have since wiped off clean install of ubuntu 9.10. goes show how want rid myself of windows on laptop.

installed 8.04 see if make connection version no avail not. have since reloaded 9.10.

chris

based on posts in section, have attached following screenshots of wireless system if data helps finding solution.
attached images attached images


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [ubuntu] D-Link DWA-652 on Toshiba Laptop


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Help needed for choosing soldering station

-
Image
my old soldering iron gave few days back. looking soldering station temperature controlled tip. came across site. has reviews these best soldering stations models . best? not sure. i heard weller wesd51 before. but, never heard hakko. yet, hakko fx888d has perfect 5 star rating amazon. plus, lot cheaper weller's. budget around $100. not know choose. wondering if of guys have used hakko fx888d before. how experience it? input helpful. thank you. been soldering 40+ years. been using hakko fx888d ~3 years, give 5 out of 5. http://www.tequipment.net/hakkofx888d-23by.html?gclid=cmvpoopevtecfqk5waodxyupyq i have 1 of these, works cheap. i hot air wand. https://www.amazon.ca/dp/b01gtyc61g/ref=pe_386430_126088100_te_item i highly recommend f888 . Arduino Forum > Using Arduino > General Electronics > Help needed for choosing sold...
Read more

Error Message when accessing Adobe

-
i downloaded recent adobe reader 8.1 , having problems opening program. i receive error message "adobe reader 8.1 has encountered problem , needs close. sorry inconvenience" i'm using windows xp i have same problem after upgrading adobe reader 7 reader 8.1.2. have repaired without success @ least 5 times. have uninstalled, downloaded, , reinstalled reader 8.1.2 @ least 5 times no success in correcting issue. i run xp media center. More discussions in Acrobat Reader adobe
Read more

Adafruit Huzzah with Arduino Uno

-
hello i want arduino work mqtt, have connected esp 01. have encountered many problems esp 01 moved adafruit huzzah breakout board. have used i2c communication between arduino , huzzah. works fine me. every time need write 2 codes 1 slave , master. there way can use these devices 1 code, mean use esp 01 module. please let me know if possible. i don't have experience i 2 c maybe there's way via protocol here's take: there macros defined each architecture. since boards have different architecture can use these macros enable appropriate code board it's running on. example, if "arduino" board avr(uno, mega, leonardo, nano, pro mini, etc.): code: [select] #ifdef __avr__ // write avr board specific code here #else // write esp8266 board specific code here #endif Arduino Forum > Using Arduino > Microcontrollers > ...
Read more